========================================== Initial Setup of the rSeries Network Layer ========================================== ----------------- rSeries Dashboard ----------------- The rSeries Dashboard will provide a visual system summary of the appliance, including **System Summary**, **Network**, **CPU**, and **Active Alarms**. It will also list the total number of vCPUs available for multitenancy and how many are currently in use. There is also a tenant overview showing a quick summary of tenant status and basic parameters. .. image:: images/initial_setup_of_rseries_network_layer/image1.png :align: center :scale: 70% The **Network** tab will provide a visual representation of all networking ports on the system. Each port will be color coded **Green** for **Up** status, and **Red** for **Down** status. The current **Pipeline** mapping is also displayed, which shows the external port mapping to internal pipelines. .. image:: images/initial_setup_of_rseries_network_layer/image2.png :align: center :scale: 70% The **CPU** tab shows all the available CPUs in the system, along with their **Current**, **5 Second**, **1 Minute**, and **5 Minute** averages. .. image:: images/initial_setup_of_rseries_network_layer/image3.png :align: center :scale: 70% The **Active Alarms** tab will display any active alerts or alarms for the system. .. image:: images/initial_setup_of_rseries_network_layer/image4.png :align: center :scale: 70% ----------------------------- F5OS Networking Configuration ----------------------------- Before configuring any tenants, you’ll need to set up networking for the F5OS platform layer. All in-band networking (interfaces, VLANs, Link Aggregation Groups) is configured within the F5OS layer, and selected VLANs are passed through to the tenant layer by the admin when deploying a tenant. This is very similar to how vCMP guests work on previous generations of BIG-IP like iSeries and VIPRION. Network Settings - > Port Groups ================================ Before configuring any interfaces, VLANs, or Link Aggregation Groups (LAG’s) you’ll need to configure the portgroups so that physical interfaces on the appliance are configured for the proper speed and bundling. The portgroup component is used to control the mode of the physical ports. This controls whether a port is bundled or unbundled, and the port speed. Currently the high-speed ports do not support unbundling. Adjacent high-speed ports (**1.0** and **2.0** on both the r5000/r10000 series) and (**11.0** & **12.0** on the r10000 series) must be configured in the same mode and speed currently. Either both are configured for 40Gb or both are configured for 100Gb; you cannot mix and match on the adjacent high-speed ports. You cannot break out these ports to lower speeds (25Gb or 10Gb) via a breakout cable as this is currently unsupported. Low speed 25Gb/10Gb ports (**3.0** - **10.0** on both the r5000/r10000 series and **13.0*** - **20.0** on the r10000 series) can be configured independently, and adjacent low speed ports can have different speed values (10Gb or 25Gb). The term, **portgroup** is used rather than simply “port” because some front panel ports may accept different types of SFPs. Depending on the portgroup mode value, a different FPGA version is loaded, and the speed of the port is adjusted accordingly. Changing the portgroup configuration will require a reboot of the appliance to load a new FPGA bitstream. The user can modify the portgroup mode as needed through the F5OS CLI, webUI or API. .. image:: images/initial_setup_of_rseries_network_layer/image5.png :align: center :scale: 70% Configuring PortGroups from the webUI ----------------------------------- To configure portgroups go to **Network Settings > Port Groups** in the F5OS webUI. This should be configured before any interface, VLAN, or LAG configuration. .. image:: images/initial_setup_of_rseries_network_layer/image6.png :align: center :scale: 70% If you do make a change, the appliance will be forced to reboot to load a new bitstream image into the FPGA. .. image:: images/initial_setup_of_rseries_network_layer/image7.png :align: center :scale: 70% Configuring PortGroups from the CLI ----------------------------------- Portgroups can be configured from the F5OS CLI using the **portgroups** command in **config** mode. The following command will set interface 10 for 10GB: .. code-block:: bash appliance-1# config Entering configuration mode terminal appliance-1(config)# portgroups portgroup 10 config mode MODE_10GB appliance-1(config-portgroup-10)# commit The following warnings were generated: 'portgroups portgroup': Portgroup mode changes result in a reboot of the box. Proceed? [yes,no] yes Commit complete. appliance-1(config-portgroup-10)# You must commit for any changes to take effect. This will require a reboot of the appliance: .. code-block:: bash appliance-1(config-portgroup-10)# commit The following warnings were generated: 'portgroups portgroup': Portgroup mode changes result in a reboot of the box. Proceed? [yes,no] yes Commit complete. appliance-1(config-portgroup-10)# Possible options for **MODE** depend on which port you are configuring. For the high-speed ports on the r10000/r5000, supported modes are: **MODE_40GB** or **MODE_100GB**. For the low-speed ports possible options for **MODE** are: **MODE_10GB** and **MODE_25GB**. You can optionally configure the portgroup **name** and ddm **poll frequency**. You can display the current configuration of the existing portgroups by running the CLI command **show running-config portgroups**. Below is the example output from an r5000 appliance: .. code-block:: bash appliance-1# show running-config portgroups portgroups portgroup 1 config name 1 config mode MODE_100GB config ddm ddm-poll-frequency 30 ! portgroups portgroup 2 config name 2 config mode MODE_100GB config ddm ddm-poll-frequency 30 ! portgroups portgroup 3 config name 3 config mode MODE_25GB config ddm ddm-poll-frequency 30 ! portgroups portgroup 4 config name 4 config mode MODE_25GB config ddm ddm-poll-frequency 30 ! portgroups portgroup 5 config name 5 config mode MODE_25GB portgroups portgroup 1 config name 1 config mode MODE_100GB config ddm ddm-poll-frequency 30 ! portgroups portgroup 2 config name 2 config mode MODE_100GB config ddm ddm-poll-frequency 30 ! portgroups portgroup 3 config name 3 config mode MODE_25GB config ddm ddm-poll-frequency 30 ! portgroups portgroup 4 config name 4 config mode MODE_25GB config ddm ddm-poll-frequency 30 ! portgroups portgroup 5 config name 5 config mode MODE_25GB config ddm ddm-poll-frequency 30 portgroups portgroup 1 config name 1 config mode MODE_100GB config ddm ddm-poll-frequency 30 ! portgroups portgroup 2 config name 2 config mode MODE_100GB config ddm ddm-poll-frequency 30 ! portgroups portgroup 3 config name 3 config mode MODE_25GB config ddm ddm-poll-frequency 30 ! portgroups portgroup 4 config name 4 config mode MODE_25GB config ddm ddm-poll-frequency 30 ! portgroups portgroup 5 config name 5 config mode MODE_25GB config ddm ddm-poll-frequency 30 ! portgroups portgroup 6 config name 6 config mode MODE_25GB config ddm ddm-poll-frequency 30 ! portgroups portgroup 7 config name 7 config mode MODE_25GB config ddm ddm-poll-frequency 30 ! portgroups portgroup 8 config name 8 config mode MODE_25GB config ddm ddm-poll-frequency 30 ! portgroups portgroup 9 config name 9 config mode MODE_25GB config ddm ddm-poll-frequency 30 ! portgroups portgroup 10 config name 10 config mode MODE_10GB config ddm ddm-poll-frequency 30 ! appliance-1# Configuring PortGroups from the API ----------------------------------- To list the current portgroup configuration, issue the following API call: .. code-block:: bash GET https://{{rseries_appliance1_ip}}:8888/restconf/data/f5-portgroup:portgroups Below is an example output from an r10000 series appliance: .. code-block:: json { "f5-portgroup:portgroups": { "portgroup": [ { "portgroup_name": "1", "config": { "name": "1", "mode": "MODE_100GB", "f5-ddm:ddm": { "ddm-poll-frequency": 30 } }, "state": { "vendor-name": "F5 NETWORKS INC.", "vendor-oui": "009065", "vendor-partnum": "OPT-0031 ", "vendor-revision": "A0", "vendor-serialnum": "X3CAU6G ", "transmitter-technology": "850 nm VCSEL", "media": "100GBASE-SR4", "optic-state": "QUALIFIED", "f5-ddm:ddm": { "rx-pwr": { "low-threshold": { "alarm": "-14.0", "warn": "-11.0" }, "instant": { "val-lane1": "-0.77", "val-lane2": "-0.89", "val-lane3": "-0.92", "val-lane4": "-1.06" }, "high-threshold": { "alarm": "3.4", "warn": "2.4" } }, "tx-pwr": { "low-threshold": { "alarm": "-10.0", "warn": "-8.0" }, "instant": { "val-lane1": "-1.11", "val-lane2": "-0.52", "val-lane3": "-1.0", "val-lane4": "-1.15" }, "high-threshold": { "alarm": "5.0", "warn": "3.0" } }, "temp": { "low-threshold": { "alarm": "-5.0", "warn": "0.0" }, "instant": { "val": "33.1523" }, "high-threshold": { "alarm": "75.0", "warn": "70.0" } }, "bias": { "low-threshold": { "alarm": "0.003", "warn": "0.005" }, "instant": { "val-lane1": "0.007536", "val-lane2": "0.007322", "val-lane3": "0.007428", "val-lane4": "0.007454" }, "high-threshold": { "alarm": "0.013", "warn": "0.011" } }, "vcc": { "low-threshold": { "alarm": "2.97", "warn": "3.135" }, "instant": { "val": "3.3211" }, "high-threshold": { "alarm": "3.63", "warn": "3.465" } } } } }, { "portgroup_name": "2", "config": { "name": "2", "mode": "MODE_100GB", "f5-ddm:ddm": { "ddm-poll-frequency": 30 } }, "state": { "vendor-name": "F5 NETWORKS INC.", "vendor-oui": "009065", "vendor-partnum": "OPT-0031 ", "vendor-revision": "A0", "vendor-serialnum": "XYR00K4 ", "transmitter-technology": "850 nm VCSEL", "media": "100GBASE-SR4", "optic-state": "QUALIFIED", "f5-ddm:ddm": { "rx-pwr": { "low-threshold": { "alarm": "-14.0", "warn": "-11.0" }, "instant": { "val-lane1": "0.05", "val-lane2": "0.12", "val-lane3": "-0.01", "val-lane4": "-0.17" }, "high-threshold": { "alarm": "3.4", "warn": "2.4" } }, "tx-pwr": { "low-threshold": { "alarm": "-10.0", "warn": "-8.0" }, "instant": { "val-lane1": "-0.93", "val-lane2": "-1.02", "val-lane3": "-1.02", "val-lane4": "-0.9" }, "high-threshold": { "alarm": "5.0", "warn": "3.0" } }, "temp": { "low-threshold": { "alarm": "-5.0", "warn": "0.0" }, "instant": { "val": "31.1953" }, "high-threshold": { "alarm": "75.0", "warn": "70.0" } }, "bias": { "low-threshold": { "alarm": "0.003", "warn": "0.005" }, "instant": { "val-lane1": "0.007448", "val-lane2": "0.007556", "val-lane3": "0.007504", "val-lane4": "0.00748" }, "high-threshold": { "alarm": "0.013", "warn": "0.011" } }, "vcc": { "low-threshold": { "alarm": "2.97", "warn": "3.135" }, "instant": { "val": "3.2964" }, "high-threshold": { "alarm": "3.63", "warn": "3.465" } } } } }, { "portgroup_name": "3", "config": { "name": "3", "mode": "MODE_25GB", "f5-ddm:ddm": { "ddm-poll-frequency": 30 } } }, { "portgroup_name": "4", "config": { "name": "4", "mode": "MODE_25GB", "f5-ddm:ddm": { "ddm-poll-frequency": 30 } } }, { "portgroup_name": "5", "config": { "name": "5", "mode": "MODE_25GB", "f5-ddm:ddm": { "ddm-poll-frequency": 30 } } }, { "portgroup_name": "6", "config": { "name": "6", "mode": "MODE_25GB", "f5-ddm:ddm": { "ddm-poll-frequency": 30 } } }, { "portgroup_name": "7", "config": { "name": "7", "mode": "MODE_25GB", "f5-ddm:ddm": { "ddm-poll-frequency": 30 } } }, { "portgroup_name": "8", "config": { "name": "8", "mode": "MODE_25GB", "f5-ddm:ddm": { "ddm-poll-frequency": 30 } } }, { "portgroup_name": "9", "config": { "name": "9", "mode": "MODE_25GB", "f5-ddm:ddm": { "ddm-poll-frequency": 30 } } }, { "portgroup_name": "10", "config": { "name": "10", "mode": "MODE_25GB", "f5-ddm:ddm": { "ddm-poll-frequency": 30 } } }, { "portgroup_name": "11", "config": { "name": "11", "mode": "MODE_100GB", "f5-ddm:ddm": { "ddm-poll-frequency": 30 } }, "state": { "vendor-name": "", "vendor-oui": "", "vendor-partnum": "", "vendor-revision": "", "vendor-serialnum": "", "transmitter-technology": "", "media": "", "optic-state": "UNKNOWN" } }, { "portgroup_name": "12", "config": { "name": "12", "mode": "MODE_100GB", "f5-ddm:ddm": { "ddm-poll-frequency": 30 } }, "state": { "vendor-name": "", "vendor-oui": "", "vendor-partnum": "", "vendor-revision": "", "vendor-serialnum": "", "transmitter-technology": "", "media": "", "optic-state": "UNKNOWN" } }, { "portgroup_name": "13", "config": { "name": "13", "mode": "MODE_25GB", "f5-ddm:ddm": { "ddm-poll-frequency": 30 } }, "state": { "vendor-name": "F5 NETWORKS INC.", "vendor-oui": "009065", "vendor-partnum": "OPT-0053 ", "vendor-revision": "A1", "vendor-serialnum": "P62BET1 ", "transmitter-technology": "", "media": "25GBASE-SR", "optic-state": "QUALIFIED", "f5-ddm:ddm": { "rx-pwr": { "low-threshold": { "alarm": "-20.0", "warn": "-18.01" }, "instant": { "val-lane1": "-0.84" }, "high-threshold": { "alarm": "4.0", "warn": "3.0" } }, "tx-pwr": { "low-threshold": { "alarm": "-9.0", "warn": "-8.0" }, "instant": { "val-lane1": "-0.8" }, "high-threshold": { "alarm": "4.0", "warn": "3.0" } }, "temp": { "low-threshold": { "alarm": "-5.0", "warn": "0.0" }, "instant": { "val": "33.0468" }, "high-threshold": { "alarm": "75.0", "warn": "70.0" } }, "bias": { "low-threshold": { "alarm": "0.001", "warn": "0.002" }, "instant": { "val-lane1": "0.007976" }, "high-threshold": { "alarm": "0.012", "warn": "0.0115" } }, "vcc": { "low-threshold": { "alarm": "3.0", "warn": "3.1" }, "instant": { "val": "3.3589" }, "high-threshold": { "alarm": "3.6", "warn": "3.5" } } } } }, { "portgroup_name": "14", "config": { "name": "14", "mode": "MODE_25GB", "f5-ddm:ddm": { "ddm-poll-frequency": 30 } }, "state": { "vendor-name": "F5 NETWORKS INC.", "vendor-oui": "009065", "vendor-partnum": "OPT-0053 ", "vendor-revision": "A1", "vendor-serialnum": "P62BESG ", "transmitter-technology": "", "media": "25GBASE-SR", "optic-state": "QUALIFIED", "f5-ddm:ddm": { "rx-pwr": { "low-threshold": { "alarm": "-20.0", "warn": "-18.01" }, "instant": { "val-lane1": "-1.45" }, "high-threshold": { "alarm": "4.0", "warn": "3.0" } }, "tx-pwr": { "low-threshold": { "alarm": "-9.0", "warn": "-8.0" }, "instant": { "val-lane1": "-0.82" }, "high-threshold": { "alarm": "4.0", "warn": "3.0" } }, "temp": { "low-threshold": { "alarm": "-5.0", "warn": "0.0" }, "instant": { "val": "32.0781" }, "high-threshold": { "alarm": "75.0", "warn": "70.0" } }, "bias": { "low-threshold": { "alarm": "0.001", "warn": "0.002" }, "instant": { "val-lane1": "0.00798" }, "high-threshold": { "alarm": "0.012", "warn": "0.0115" } }, "vcc": { "low-threshold": { "alarm": "3.0", "warn": "3.1" }, "instant": { "val": "3.3499" }, "high-threshold": { "alarm": "3.6", "warn": "3.5" } } } } }, { "portgroup_name": "15", "config": { "name": "15", "mode": "MODE_25GB", "f5-ddm:ddm": { "ddm-poll-frequency": 30 } }, "state": { "vendor-name": "F5 NETWORKS INC.", "vendor-oui": "009065", "vendor-partnum": "OPT-0053 ", "vendor-revision": "A1", "vendor-serialnum": "P62BET3 ", "transmitter-technology": "", "media": "25GBASE-SR", "optic-state": "QUALIFIED", "f5-ddm:ddm": { "rx-pwr": { "low-threshold": { "alarm": "-20.0", "warn": "-18.01" }, "instant": { "val-lane1": "-0.66" }, "high-threshold": { "alarm": "4.0", "warn": "3.0" } }, "tx-pwr": { "low-threshold": { "alarm": "-9.0", "warn": "-8.0" }, "instant": { "val-lane1": "-0.61" }, "high-threshold": { "alarm": "4.0", "warn": "3.0" } }, "temp": { "low-threshold": { "alarm": "-5.0", "warn": "0.0" }, "instant": { "val": "30.2812" }, "high-threshold": { "alarm": "75.0", "warn": "70.0" } }, "bias": { "low-threshold": { "alarm": "0.001", "warn": "0.002" }, "instant": { "val-lane1": "0.008008" }, "high-threshold": { "alarm": "0.012", "warn": "0.0115" } }, "vcc": { "low-threshold": { "alarm": "3.0", "warn": "3.1" }, "instant": { "val": "3.3101" }, "high-threshold": { "alarm": "3.6", "warn": "3.5" } } } } }, { "portgroup_name": "16", "config": { "name": "16", "mode": "MODE_25GB", "f5-ddm:ddm": { "ddm-poll-frequency": 30 } }, "state": { "vendor-name": "F5 NETWORKS INC.", "vendor-oui": "009065", "vendor-partnum": "OPT-0053 ", "vendor-revision": "A1", "vendor-serialnum": "P62BET5 ", "transmitter-technology": "", "media": "25GBASE-SR", "optic-state": "QUALIFIED", "f5-ddm:ddm": { "rx-pwr": { "low-threshold": { "alarm": "-20.0", "warn": "-18.01" }, "instant": { "val-lane1": "-0.68" }, "high-threshold": { "alarm": "4.0", "warn": "3.0" } }, "tx-pwr": { "low-threshold": { "alarm": "-9.0", "warn": "-8.0" }, "instant": { "val-lane1": "-0.82" }, "high-threshold": { "alarm": "4.0", "warn": "3.0" } }, "temp": { "low-threshold": { "alarm": "-5.0", "warn": "0.0" }, "instant": { "val": "32.4921" }, "high-threshold": { "alarm": "75.0", "warn": "70.0" } }, "bias": { "low-threshold": { "alarm": "0.001", "warn": "0.002" }, "instant": { "val-lane1": "0.007994" }, "high-threshold": { "alarm": "0.012", "warn": "0.0115" } }, "vcc": { "low-threshold": { "alarm": "3.0", "warn": "3.1" }, "instant": { "val": "3.3442" }, "high-threshold": { "alarm": "3.6", "warn": "3.5" } } } } }, { "portgroup_name": "17", "config": { "name": "17", "mode": "MODE_25GB", "f5-ddm:ddm": { "ddm-poll-frequency": 30 } } }, { "portgroup_name": "18", "config": { "name": "18", "mode": "MODE_25GB", "f5-ddm:ddm": { "ddm-poll-frequency": 30 } } }, { "portgroup_name": "19", "config": { "name": "19", "mode": "MODE_25GB", "f5-ddm:ddm": { "ddm-poll-frequency": 30 } } }, { "portgroup_name": "20", "config": { "name": "20", "mode": "MODE_10GB", "f5-ddm:ddm": { "ddm-poll-frequency": 30 } } } ] } } To change the portgroup configuration via the API, use the following API call. .. code-block:: bash PATCH https://{{rseries_appliance1_ip}}:8888/restconf/data/f5-portgroup:portgroups Below is an example configuration change in the body of the API call, this is changing portgroup 10 to 25Gb mode: .. code-block:: json { "f5-portgroup:portgroups": { "portgroup": [ { "portgroup_name": "10", "config": { "mode": "MODE_25GB" } } ] } } Network Settings -> Interfaces ============================== Interface numbering will vary depending on which rSeries model is being used. Interfaces will always be numbered by **.0** for rSeries appliances. The r10000 has a total of 20 ports labeled **1.0** - **20.0**, and the r5000 has 10 ports labeled **1.0** - **10.0**. .. image:: images/initial_setup_of_rseries_network_layer/image9.png :align: center :scale: 70% .. image:: images/initial_setup_of_rseries_network_layer/image8.png :align: center :scale: 70% Configuring Interfaces from the webUI ----------------------------------- Within the F5OS webUI, the physical ports of the appliance will be visible by going to **Network Settings > Interfaces** page. .. image:: images/initial_setup_of_rseries_network_layer/image10.png :align: center :scale: 70% You can click on any interface to view its settings or edit them. You can currently change the interface state via the webUI or the **Native VLAN** (untagged) and **Trunk VLANs** (tagged) if the interface is not part of a LAG. If the interface is part of a LAG, then the VLAN configuration is done within the LAG rather than the interface. .. image:: images/initial_setup_of_rseries_network_layer/image11.png :align: center :scale: 70% Configuring Interfaces from the CLI ----------------------------------- Interfaces can be configured in the F5OS CLI. As mentioned previously, portgroups should be configured for their desired state before configuring any interfaces. In the CLI, enter config mode and then specify the interface you want to configure. If the interface is going to be part of a LAG, then most of the configuration is done within the LAG. Use the command **show running-config interfaces** to see the current configuration: .. code-block:: bash appliance-1# show running-config interfaces interfaces interface 1.0 config name 1.0 config type ethernetCsmacd config enabled ethernet config aggregate-id Arista ! interfaces interface 2.0 config name 2.0 config type ethernetCsmacd config enabled ethernet config aggregate-id Arista ! interfaces interface 3.0 config name 3.0 config type ethernetCsmacd config enabled ! interfaces interface 4.0 config name 4.0 config type ethernetCsmacd config enabled ! interfaces interface 5.0 config name 5.0 config type ethernetCsmacd config enabled ! interfaces interface 6.0 config name 6.0 config type ethernetCsmacd config enabled ! interfaces interface 7.0 config name 7.0 config type ethernetCsmacd config enabled ! interfaces interface 8.0 config name 8.0 config type ethernetCsmacd config enabled ethernet config aggregate-id HA-Interconnect ! interfaces interface 9.0 config name 9.0 config type ethernetCsmacd config enabled ethernet config aggregate-id HA-Interconnect ! interfaces interface 10.0 config name 10.0 config type ethernetCsmacd config enabled ! interfaces interface mgmt config name mgmt config type ethernetCsmacd config enabled ethernet config auto-negotiate true ethernet config duplex-mode FULL ethernet config port-speed SPEED_1GB ! interfaces interface Arista config name Arista config type ieee8023adLag aggregation config lag-type LACP aggregation config distribution-hash src-dst-ipport aggregation switched-vlan config trunk-vlans [ 3010 3011 ] ! interfaces interface HA-Interconnect config name HA-Interconnect config type ieee8023adLag aggregation config lag-type LACP aggregation config distribution-hash src-dst-ipport aggregation switched-vlan config trunk-vlans [ 500 ] ! appliance-1# To make any changes, you will need to enter **config** mode and then enter the interface config mode to make changes. The example below is adding an 802.1Q tagged VLAN 500 to interface 6.0. Be sure to commit any changes as they don’t take effect until the commit is issued. .. code-block:: bash appliance-1# config Entering configuration mode terminal appliance-1(config)# interfaces interface 6.0 ethernet switched-vlan config trunk-vlans 500 appliance-1(config-interface-6.0)# commit Commit complete. appliance-1(config-interface-6.0)# Configuring Interfaces from the API ----------------------------------- The following API command will list all the current interfaces within the appliance with their configuration and status: .. code-block:: bash GET https://{{rseries_appliance1_ip}}:8888/restconf/data/openconfig-interfaces:interfaces .. code-block:: json { "openconfig-interfaces:interfaces": { "interface": [ { "name": "1.0", "config": { "name": "1.0", "type": "iana-if-type:ethernetCsmacd", "enabled": true }, "state": { "name": "1.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 19, "oper-status": "UP", "counters": { "in-octets": "9086600", "in-unicast-pkts": "116", "in-broadcast-pkts": "1493", "in-multicast-pkts": "68814", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "187008", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "1461", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_UP" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_100GB", "openconfig-if-aggregate:aggregate-id": "Arista" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_100GB", "hw-mac-address": "00:94:a1:69:59:0d", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "2.0", "config": { "name": "2.0", "type": "iana-if-type:ethernetCsmacd", "enabled": true }, "state": { "name": "2.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 24, "oper-status": "UP", "counters": { "in-octets": "6288468", "in-unicast-pkts": "80", "in-broadcast-pkts": "504", "in-multicast-pkts": "46884", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "192776", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "1522", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_UP" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_100GB", "openconfig-if-aggregate:aggregate-id": "Arista" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_100GB", "hw-mac-address": "00:94:a1:69:59:12", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "3.0", "config": { "name": "3.0", "type": "iana-if-type:ethernetCsmacd", "enabled": true }, "state": { "name": "3.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 20, "oper-status": "DOWN", "counters": { "in-octets": "0", "in-unicast-pkts": "0", "in-broadcast-pkts": "0", "in-multicast-pkts": "0", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "0", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "0", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_DEFAULTED" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_25GB" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "hw-mac-address": "00:94:a1:69:59:0e", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "4.0", "config": { "name": "4.0", "type": "iana-if-type:ethernetCsmacd", "enabled": true }, "state": { "name": "4.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 21, "oper-status": "DOWN", "counters": { "in-octets": "0", "in-unicast-pkts": "0", "in-broadcast-pkts": "0", "in-multicast-pkts": "0", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "0", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "0", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_DEFAULTED" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_25GB" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "hw-mac-address": "00:94:a1:69:59:0f", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "5.0", "config": { "name": "5.0", "type": "iana-if-type:ethernetCsmacd", "enabled": true }, "state": { "name": "5.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 22, "oper-status": "DOWN", "counters": { "in-octets": "0", "in-unicast-pkts": "0", "in-broadcast-pkts": "0", "in-multicast-pkts": "0", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "0", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "0", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_DEFAULTED" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_25GB" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "hw-mac-address": "00:94:a1:69:59:10", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "6.0", "config": { "name": "6.0", "type": "iana-if-type:ethernetCsmacd", "enabled": true }, "state": { "name": "6.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 23, "oper-status": "DOWN", "counters": { "in-octets": "0", "in-unicast-pkts": "0", "in-broadcast-pkts": "0", "in-multicast-pkts": "0", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "0", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "0", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_DEFAULTED" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_25GB" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "hw-mac-address": "00:94:a1:69:59:11", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "7.0", "config": { "name": "7.0", "type": "iana-if-type:ethernetCsmacd", "enabled": true }, "state": { "name": "7.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 25, "oper-status": "DOWN", "counters": { "in-octets": "0", "in-unicast-pkts": "0", "in-broadcast-pkts": "0", "in-multicast-pkts": "0", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "0", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "0", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_DEFAULTED" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_25GB" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "hw-mac-address": "00:94:a1:69:59:13", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "8.0", "config": { "name": "8.0", "type": "iana-if-type:ethernetCsmacd", "enabled": true }, "state": { "name": "8.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 26, "oper-status": "DOWN", "counters": { "in-octets": "0", "in-unicast-pkts": "0", "in-broadcast-pkts": "0", "in-multicast-pkts": "0", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "0", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "0", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_DEFAULTED" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_25GB" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "hw-mac-address": "00:94:a1:69:59:14", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "9.0", "config": { "name": "9.0", "type": "iana-if-type:ethernetCsmacd", "enabled": true }, "state": { "name": "9.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 27, "oper-status": "DOWN", "counters": { "in-octets": "0", "in-unicast-pkts": "0", "in-broadcast-pkts": "0", "in-multicast-pkts": "0", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "0", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "0", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_DEFAULTED" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_25GB" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "hw-mac-address": "00:94:a1:69:59:15", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "10.0", "config": { "name": "10.0", "type": "iana-if-type:ethernetCsmacd", "enabled": true }, "state": { "name": "10.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 28, "oper-status": "DOWN", "counters": { "in-octets": "0", "in-unicast-pkts": "0", "in-broadcast-pkts": "0", "in-multicast-pkts": "0", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "0", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "0", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_DEFAULTED" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_25GB" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "hw-mac-address": "00:94:a1:69:59:16", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "11.0", "config": { "name": "11.0", "type": "iana-if-type:ethernetCsmacd", "enabled": true }, "state": { "name": "11.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 9, "oper-status": "DOWN", "counters": { "in-octets": "0", "in-unicast-pkts": "0", "in-broadcast-pkts": "0", "in-multicast-pkts": "0", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "0", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "0", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_DEFAULTED" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_100GB" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_100GB", "hw-mac-address": "00:94:a1:69:59:03", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "12.0", "config": { "name": "12.0", "type": "iana-if-type:ethernetCsmacd", "enabled": true }, "state": { "name": "12.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 14, "oper-status": "DOWN", "counters": { "in-octets": "0", "in-unicast-pkts": "0", "in-broadcast-pkts": "0", "in-multicast-pkts": "0", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "0", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "0", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_DEFAULTED" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_100GB" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_100GB", "hw-mac-address": "00:94:a1:69:59:08", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "13.0", "config": { "name": "13.0", "type": "iana-if-type:ethernetCsmacd", "enabled": true }, "state": { "name": "13.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 10, "oper-status": "UP", "counters": { "in-octets": "5605888", "in-unicast-pkts": "0", "in-broadcast-pkts": "0", "in-multicast-pkts": "43796", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "5608964", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "43828", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_UP" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "openconfig-if-aggregate:aggregate-id": "HA-Interconnect" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "hw-mac-address": "00:94:a1:69:59:04", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "14.0", "config": { "name": "14.0", "type": "iana-if-type:ethernetCsmacd", "enabled": true }, "state": { "name": "14.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 11, "oper-status": "UP", "counters": { "in-octets": "5605888", "in-unicast-pkts": "0", "in-broadcast-pkts": "0", "in-multicast-pkts": "43796", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "5606144", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "43798", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_UP" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "openconfig-if-aggregate:aggregate-id": "HA-Interconnect" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "hw-mac-address": "00:94:a1:69:59:05", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "15.0", "config": { "name": "15.0", "type": "iana-if-type:ethernetCsmacd", "enabled": true }, "state": { "name": "15.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 12, "oper-status": "UP", "counters": { "in-octets": "5605120", "in-unicast-pkts": "0", "in-broadcast-pkts": "0", "in-multicast-pkts": "43790", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "5606272", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "43799", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_UP" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "openconfig-if-aggregate:aggregate-id": "HA-Interconnect" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "hw-mac-address": "00:94:a1:69:59:06", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "16.0", "config": { "name": "16.0", "type": "iana-if-type:ethernetCsmacd", "enabled": true }, "state": { "name": "16.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 13, "oper-status": "UP", "counters": { "in-octets": "5603328", "in-unicast-pkts": "0", "in-broadcast-pkts": "0", "in-multicast-pkts": "43776", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "5603456", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "43777", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_UP" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "openconfig-if-aggregate:aggregate-id": "HA-Interconnect" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "hw-mac-address": "00:94:a1:69:59:07", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "17.0", "config": { "name": "17.0", "type": "iana-if-type:ethernetCsmacd", "enabled": true }, "state": { "name": "17.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 15, "oper-status": "DOWN", "counters": { "in-octets": "0", "in-unicast-pkts": "0", "in-broadcast-pkts": "0", "in-multicast-pkts": "0", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "0", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "0", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_DEFAULTED" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_25GB" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "hw-mac-address": "00:94:a1:69:59:09", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "18.0", "config": { "name": "18.0", "type": "iana-if-type:ethernetCsmacd", "enabled": true }, "state": { "name": "18.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 16, "oper-status": "DOWN", "counters": { "in-octets": "0", "in-unicast-pkts": "0", "in-broadcast-pkts": "0", "in-multicast-pkts": "0", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "0", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "0", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_DEFAULTED" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_25GB" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "hw-mac-address": "00:94:a1:69:59:0a", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "19.0", "config": { "name": "19.0", "type": "iana-if-type:ethernetCsmacd", "enabled": true }, "state": { "name": "19.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 17, "oper-status": "DOWN", "counters": { "in-octets": "0", "in-unicast-pkts": "0", "in-broadcast-pkts": "0", "in-multicast-pkts": "0", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "0", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "0", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_DEFAULTED" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_25GB" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "hw-mac-address": "00:94:a1:69:59:0b", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "20.0", "config": { "name": "20.0", "type": "iana-if-type:ethernetCsmacd", "enabled": true }, "state": { "name": "20.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 18, "oper-status": "DOWN", "counters": { "in-octets": "0", "in-unicast-pkts": "0", "in-broadcast-pkts": "0", "in-multicast-pkts": "0", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "0", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "0", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_DEFAULTED" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_10GB" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_10GB", "hw-mac-address": "00:94:a1:69:59:0c", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "mgmt", "config": { "name": "mgmt", "type": "iana-if-type:ethernetCsmacd", "enabled": true }, "state": { "name": "mgmt", "type": "iana-if-type:ethernetCsmacd", "enabled": true, "ifindex": 1, "oper-status": "UP", "counters": { "in-octets": "47748466", "in-unicast-pkts": "24169", "in-broadcast-pkts": "274573", "in-multicast-pkts": "63421", "in-discards": "0", "in-errors": "0", "out-octets": "22171273", "out-unicast-pkts": "30177", "out-broadcast-pkts": "50", "out-multicast-pkts": "71", "out-discards": "0", "out-errors": "0" } }, "openconfig-if-ethernet:ethernet": { "config": { "auto-negotiate": true, "duplex-mode": "FULL", "port-speed": "openconfig-if-ethernet:SPEED_1GB" }, "state": { "auto-negotiate": true, "duplex-mode": "FULL", "port-speed": "openconfig-if-ethernet:SPEED_1GB", "hw-mac-address": "00:94:a1:69:59:02", "negotiated-duplex-mode": "FULL", "negotiated-port-speed": "openconfig-if-ethernet:SPEED_1GB", "counters": { "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-crc-errors": "0", "out-mac-pause-frames": "0" } } } }, { "name": "Arista", "config": { "name": "Arista", "type": "iana-if-type:ieee8023adLag", "enabled": true }, "state": { "name": "Arista", "type": "iana-if-type:ieee8023adLag", "mtu": 9600, "enabled": true, "oper-status": "UP", "f5-interface:forward-error-correction": "auto" }, "openconfig-if-aggregate:aggregation": { "config": { "lag-type": "LACP", "f5-if-aggregate:distribution-hash": "src-dst-ipport" }, "state": { "lag-type": "LACP", "lag-speed": 200, "f5-if-aggregate:distribution-hash": "src-dst-ipport", "f5-if-aggregate:mac-address": "00:94:a1:69:59:24", "f5-if-aggregate:lagid": 1 }, "openconfig-vlan:switched-vlan": { "config": { "trunk-vlans": [ 3010, 3011 ] } } } }, { "name": "HA-Interconnect", "config": { "name": "HA-Interconnect", "type": "iana-if-type:ieee8023adLag", "enabled": true }, "state": { "name": "HA-Interconnect", "type": "iana-if-type:ieee8023adLag", "mtu": 9600, "enabled": true, "oper-status": "UP", "f5-interface:forward-error-correction": "auto" }, "openconfig-if-aggregate:aggregation": { "config": { "lag-type": "LACP", "f5-if-aggregate:distribution-hash": "src-dst-ipport" }, "state": { "lag-type": "LACP", "lag-speed": 100, "f5-if-aggregate:distribution-hash": "src-dst-ipport", "f5-if-aggregate:mac-address": "00:94:a1:69:59:25", "f5-if-aggregate:lagid": 2 }, "openconfig-vlan:switched-vlan": { "config": { "trunk-vlans": [ 500 ] } } } } ] } } To configure interfaces (that are not part of a LAG), use the following PATCH API call. In the example below, VLANs are being assigned to the physical interfaces. .. code-block:: bash PATCH https://{{rseries_appliance1_ip}}:8888/restconf/data/openconfig-interfaces:interfaces .. code-block:: json { "openconfig-interfaces:interfaces": { "interface": [ { "name": "6.0", "openconfig-if-ethernet:ethernet": { "openconfig-vlan:switched-vlan": { "config": { "trunk-vlans": [ 501 ] } } } }, { "name": "2.0", "openconfig-if-ethernet:ethernet": { "openconfig-vlan:switched-vlan": { "config": { "trunk-vlans": [ 444, 555 ] } } } } ] } } Network Settings -> VLANs ========================= All in-band networking, including VLANs, is configured in the F5OS layer, and just like vCMP guests inherit VLANs, VLANs will be inherited by rSeries tenants. This allows administrators to assign the VLANs that are authorized for use by the tenant at the F5OS layer, and then within the tenant there is no ability to configure lower-level networking like interfaces, LAGs and VLANs. rSeries supports both tagged (802.1Q) and untagged VLAN interfaces externally. VLANs can be configured from the CLI, webUI, or API. **Note: 802.1Q-in-Q (double VLAN tagging) is not currently supported on the rSeries platform.** Configuring VLANs from the webUI ------------------------------ VLANs can be created in the F5OS webUI under **Network Settings > VLANs**. When adding a new VLAN you will define a **Name** and a **VLAN ID**. When you assign this VLAN to an interface or LAG you will determine if you want it to be untagged by configuring it as a **Native VLAN** or tagged by adding it as a **Trunked VLAN**. .. image:: images/initial_setup_of_rseries_network_layer/image12.png :align: center :scale: 70% .. image:: images/initial_setup_of_rseries_network_layer/image13.png :align: center :scale: 70% Configuring VLANs from the CLI ------------------------------ VLANs can be configured within the F5OS CLI. Once VLANs are created, they can be assigned to either a physical interface or LAG within the appliance. VLANs must be given a name and a VLAN ID. You can choose if a VLAN is tagged or untagged within the physical interface or LAG configuration. To show the current configured VLANs and their options, use the command **show running-config vlans**. .. code-block:: bash appliance-1# show running-config vlans vlans vlan 500 config vlan-id 500 config name Tenant1-HA-VLAN ! vlans vlan 501 config vlan-id 501 config name HA-VLAN2 ! vlans vlan 3010 config vlan-id 3010 config name Internal-VLAN ! vlans vlan 3011 config vlan-id 3011 config name External-VLAN ! appliance-1# You can also see the configured state of VLANs by running the **show vlans** command: .. code-block:: bash appliance-1# show vlans VLAN ID INTERFACE ----------------------- 500 6.0 HA-Interconnect 501 3010 Arista 3011 Arista appliance-1# There are a few other VLAN related commands to show the configuration and running state of **vlan-listeners**. The command **show running-config vlan-listeners** will show the current configuration. A VLAN listener is created for each VLAN and is responsible for rebroadcasting traffic within the VLAN. **NOTE: For shared VLANs among different tenants, the VLAN must be tied to an external interface or LAG in order for the VLAN listener to be created.** .. code-block:: bash Boston-r10900-1# show running-config vlan-listeners vlan-listeners vlan-listener Arista 3010 config entry-type VLAN-LISTENER config owner tenant1 config ifh-fields ndi-id 4095 config ifh-fields svc 8 config ifh-fields sep 15 config ifh-fields mirroring disabled ! vlan-listeners vlan-listener Arista 3011 config entry-type VLAN-LISTENER config owner tenant1 config ifh-fields ndi-id 4095 config ifh-fields svc 8 config ifh-fields sep 15 config ifh-fields mirroring disabled ! vlan-listeners vlan-listener HA-Interconnect 500 config entry-type VLAN-LISTENER config owner tenant1 config ifh-fields ndi-id 4095 config ifh-fields svc 8 config ifh-fields sep 15 config ifh-fields mirroring disabled ! Boston-r10900-1# The **show vlan-listeners** command will show the current state: .. code-block:: bash Boston-r10900-1# show vlan-listeners NDI SERVICE INTERFACE VLAN ENTRY TYPE OWNER ID SVC VTC SEP DMS DID CMDS MIRRORING IDS -------------------------------------------------------------------------------------------------------- Arista 3010 VLAN-LISTENER tenant1 4095 8 - 15 - - - disabled - Arista 3011 VLAN-LISTENER tenant1 4095 8 - 15 - - - disabled - HA-Interconnect 500 VLAN-LISTENER tenant1 4095 8 - 15 - - - disabled - Boston-r10900-1# Configuring VLANs from the API ------------------------------ To configure VLANs, use the following API command and JSON body. This will configure VLANs along with their VLAN IDs. After the VLANs are created, you will be able to assign them to either interfaces or LAGs. .. code-block:: bash PATCH https://{{rseries_appliance1_ip}}:8888/restconf/data/ .. code-block:: json { "openconfig-vlan:vlans": { "vlan": [ { "vlan-id": "3010", "config": { "vlan-id": 3010, "name": "Internal-VLAN" } }, { "vlan-id": "3011", "config": { "vlan-id": 3011, "name": "External-VLAN" } }, { "vlan-id": "500", "config": { "vlan-id": 500, "name": "HA-VLAN" } }, { "vlan-id": "501", "config": { "vlan-id": 501, "name": "HA-VLAN-Tenant1" } }, { "vlan-id": "502", "config": { "vlan-id": 502, "name": "HA-VLAN-Tenant2" } }, { "vlan-id": "503", "config": { "vlan-id": 503, "name": "HA-VLAN-Tenant3" } } ] } } The following command will list the configuration and status of all VLANs within the appliance: .. code-block:: bash GET https://{{rseries_appliance1_ip}}:8888/restconf/data/openconfig-vlan:vlans .. code-block:: json { "openconfig-vlan:vlans": { "vlan": [ { "vlan-id": 500, "config": { "vlan-id": 500, "name": "HA-VLAN" } }, { "vlan-id": 501, "config": { "vlan-id": 501, "name": "HA-VLAN-Tenant1" } }, { "vlan-id": 502, "config": { "vlan-id": 502, "name": "HA-VLAN-Tenant2" } }, { "vlan-id": 503, "config": { "vlan-id": 503, "name": "HA-VLAN-Tenant3" } }, { "vlan-id": 3010, "config": { "vlan-id": 3010, "name": "Internal-VLAN" } }, { "vlan-id": 3011, "config": { "vlan-id": 3011, "name": "External-VLAN" } } ] } } Network Settings -> LAGs ======================== All in-band networking, including Link Aggregation Groups (LAGs), is configured in the F5OS layer. The admin will configure interfaces and/or LAGs and they will assign VLANs to those physical interfaces or LAGs. Tenants will then inherit the VLANs that are assigned to them when they are created. It is recommended to spread LAG members across internal rSeries pipelines for added redundancy and optimal performance. Configuring LAGs from the webUI ----------------------------- Link Aggregation Groups (LAGs) can be configured in the F5OS webUI via the **Network Settings > LAGs** page: .. image:: images/initial_setup_of_rseries_network_layer/image14.png :align: center :scale: 70% You can add a new LAG or edit an existing one. For **LAG Type** the options are **LACP** or **STATIC**. If you choose LACP then you have additional options for **LACP Interval** (**SLOW** or **FAST**) and **LACP Mode** (**ACTIVE** or **PASSIVE**). LACP best practices should follow previous BIG-IP examples as outlined in the links below. Note in BIG-IP the term **Trunks** is used in place of LAG which is used in F5OS: https://support.f5.com/csp/article/K1689 https://support.f5.com/csp/article/K13142 The following solution article provides guidance for setting up VELOS LAG interfaces and LACP with Cisco Nexus 9000 series switches, and this would be similar guidance for rSeries: https://support.f5.com/csp/article/K33431212 Once you have configured the **LAG Type** and LACP options, you can add any physical interfaces within the rSeries appliance to be part of a LAG. Finally, you can configure the **Native VLAN** (for untagged VLAN), and what **Trunked VLANs** (tagged) you’d like to add to this LAG interface. .. image:: images/initial_setup_of_rseries_network_layer/image15.png :align: center :scale: 70% Configuring LAGs from the CLI ----------------------------- Within the webUI, LAGs and LACP parameters are configured within the LAG webUI pages. In the CLI they are broken out into separate areas. First enter **config** mode and then use the following interface commands to configure the aggregation and LACP: .. code-block:: bash appliance-1(config)# interfaces interface Arista appliance-1(config-interface-Arista)# config name Arista appliance-1(config-interface-Arista)# config type ieee8023adLag appliance-1(config-interface-Arista)# aggregation config lag-type LACP appliance-1(config-interface-Arista)# aggregation config distribution-hash src-dst-ipport appliance-1(config-interface-Arista)# aggregation switched-vlan config trunk-vlans [ 3010 3011 ] appliance-1(config-interface-Arista)# commit Commit complete. appliance-1(config-interface-Arista)# appliance-1(config)# interfaces interface HA-Interconnect appliance-1(config-interface-HA-Interconnect)# config name HA-Interconnect appliance-1(config-interface-HA-Interconnect)# config type ieee8023adLag appliance-1(config-interface-HA-Interconnect)# aggregation config lag-type LACP appliance-1(config-interface-HA-Interconnect)# aggregation config distribution-hash src-dst-ipport appliance-1(config-interface-HA-Interconnect)# aggregation switched-vlan config trunk-vlans [ 500 ] appliance-1(config-interface-HA-Interconnect)# commit Commit complete. appliance-1(config-interface-Arista)# You can view the current interface aggregation configurations in the CLI by running the command **show running-config interfaces interface aggregation** command. This will show the current aggregation interfaces, lag-type, distribution hash, and VLANs assigned to each lag: .. code-block:: bash appliance-1# show running-config interfaces interface aggregation interfaces interface Arista aggregation config lag-type LACP aggregation config distribution-hash src-dst-ipport aggregation switched-vlan config trunk-vlans [ 3010 3011 ] ! interfaces interface HA-Interconnect aggregation config lag-type LACP aggregation config distribution-hash src-dst-ipport aggregation switched-vlan config trunk-vlans [ 500 ] ! appliance-1# Next, you must configure interfaces to be part of the LAG. Below are examples of interface 1.0 and 2.0 being added to the aggregate-id **Arista**, and interfaces 8.0 and 9.0 being added to the aggregate **HA-Interconnect**. .. code-block:: bash appliance-1(config)# interfaces interface 1.0 appliance-1(config-interface-1.0)# config name 1.0 appliance-1(config-interface-1.0)# ethernet config aggregate-id Arista appliance-1(config-interface-1.0)# exit appliance-1(config)# interfaces interface 2.0 appliance-1(config-interface-2.0)# config name 2.0 appliance-1(config-interface-2.0)# ethernet config aggregate-id Arista appliance-1(config-interface-2.0)# exit appliance-1(config)# interfaces interface 8.0 appliance-1(config-interface-1.0)# config name 8.0 appliance-1(config-interface-1.0)# ethernet config aggregate-id HA-Interconnect appliance-1(config-interface-1.0)# exit appliance-1(config)# interfaces interface 9.0 appliance-1(config-interface-2.0)# config name 9.0 appliance-1(config-interface-2.0)# ethernet config aggregate-id HA-Interconnect appliance-1(config-interface-2.0)# ! appliance-1(config)# commit Finally, configuring the lacp interfaces for **Arista** and **HA-Interconnect** will start to bring the LAG interface up. .. code-block:: bash appliance-1# config Entering configuration mode terminal appliance-1(config)# lacp interfaces interface Arista appliance-1(config-interface-Arista)# config name Arista appliance-1(config-interface-Arista)# config interval FAST appliance-1(config-interface-Arista)# config lacp-mode ACTIVE appliance-1(config-interface-Arista)# ! appliance-1(config-interface-Arista)# commit Commit complete. appliance-1# config Entering configuration mode terminal appliance-1(config)# lacp interfaces interface HA-Interconnect appliance-1(config-interface-HA-Interconnect)# config name HA-Interconnect appliance-1(config-interface-HA-Interconnect)# config interval FAST appliance-1(config-interface-HA-Interconnect)# config lacp-mode ACTIVE appliance-1(config-interface-HA-Interconnect)# ! appliance-1(config-interface-HA-Interconnect)# commit Commit complete. You can also view the current LACP configuration for each LAG by issuing the **show running-config lacp** CLI command. This will show all the LACP parameters such as the system priority, name, interval, and lacp-mode for each LAG. .. code-block:: bash appliance-1# show running-config lacp lacp config system-priority 32768 lacp interfaces interface Arista config name Arista config interval FAST config lacp-mode ACTIVE ! lacp interfaces interface HA-Interconnect config name HA-Interconnect config interval FAST config lacp-mode ACTIVE ! appliance-1# To see the status of the LACP interfaces, run the command **show lacp**. It is best to widen your terminal screen as the output is dynamic and will display better on a wider terminal screen in more of a table format: .. code-block:: bash appliance-1# show lacp lacp state system-id-mac 00:94:a1:69:35:13 PARTNER LACP LACP LACP LACP LACP LACP SYSTEM OPER PARTNER PORT PORT IN OUT RX TX UNKNOWN LACP NAME NAME INTERVAL MODE SYSTEM ID MAC PRIORITY INTERFACE INTERFACE ACTIVITY TIMEOUT SYNCHRONIZATION AGGREGATABLE COLLECTING DISTRIBUTING SYSTEM ID KEY PARTNER ID KEY NUM NUM PKTS PKTS ERRORS ERRORS ERRORS ERRORS ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ Arista Arista FAST ACTIVE 0:94:a1:69:35:13 - 1.0 - ACTIVE SHORT IN_SYNC true true true 0:94:a1:69:35:13 2 2c:dd:e9:90:88:13 103 1024 345 237602 7889 0 0 0 0 2.0 - ACTIVE SHORT IN_SYNC true true true 0:94:a1:69:35:13 2 2c:dd:e9:90:88:13 103 2048 349 237590 7888 0 0 0 0 HA-Interconnect HA-Interconnect FAST ACTIVE 0:94:a1:69:35:13 - 8.0 - ACTIVE SHORT IN_SYNC true true true 0:94:a1:69:35:13 3 0:94:a1:69:29:13 3 8192 8192 237494 236522 0 0 0 0 9.0 - ACTIVE SHORT IN_SYNC true true true 0:94:a1:69:35:13 3 0:94:a1:69:29:13 3 9216 9216 237488 236516 0 0 0 0 appliance-1# If you have shorter width terminal, then the output above may be condensed as seen below: .. code-block:: bash appliance-1# show lacp lacp state system-id-mac 00:94:a1:69:35:13 lacp interfaces interface Arista state name Arista state interval FAST state lacp-mode ACTIVE state system-id-mac 0:94:a1:69:35:13 members member 1.0 state activity ACTIVE state timeout SHORT state synchronization IN_SYNC state aggregatable true state collecting true state distributing true state system-id 0:94:a1:69:35:13 state oper-key 2 state partner-id 2c:dd:e9:90:88:13 state partner-key 103 state port-num 1024 state partner-port-num 345 state counters lacp-in-pkts 237650 state counters lacp-out-pkts 7891 state counters lacp-rx-errors 0 state counters lacp-tx-errors 0 state counters lacp-unknown-errors 0 state counters lacp-errors 0 members member 2.0 state activity ACTIVE state timeout SHORT state synchronization IN_SYNC state aggregatable true state collecting true state distributing true state system-id 0:94:a1:69:35:13 state oper-key 2 state partner-id 2c:dd:e9:90:88:13 state partner-key 103 state port-num 2048 state partner-port-num 349 state counters lacp-in-pkts 237638 state counters lacp-out-pkts 7890 state counters lacp-rx-errors 0 state counters lacp-tx-errors 0 state counters lacp-unknown-errors 0 state counters lacp-errors 0 lacp interfaces interface HA-Interconnect state name HA-Interconnect state interval FAST state lacp-mode ACTIVE state system-id-mac 0:94:a1:69:35:13 members member 8.0 state activity ACTIVE state timeout SHORT state synchronization IN_SYNC state aggregatable true state collecting true state distributing true state system-id 0:94:a1:69:35:13 state oper-key 3 state partner-id 0:94:a1:69:29:13 state partner-key 3 state port-num 8192 state partner-port-num 8192 state counters lacp-in-pkts 237542 state counters lacp-out-pkts 236570 state counters lacp-rx-errors 0 state counters lacp-tx-errors 0 state counters lacp-unknown-errors 0 state counters lacp-errors 0 members member 9.0 state activity ACTIVE state timeout SHORT state synchronization IN_SYNC state aggregatable true state collecting true state distributing true state system-id 0:94:a1:69:35:13 state oper-key 3 state partner-id 0:94:a1:69:29:13 state partner-key 3 state port-num 9216 state partner-port-num 9216 state counters lacp-in-pkts 237536 state counters lacp-out-pkts 236564 state counters lacp-rx-errors 0 state counters lacp-tx-errors 0 state counters lacp-unknown-errors 0 state counters lacp-errors 0 appliance1# Configuring LAGs from the API ----------------------------- To create a LAG, add interfaces to it, and add proper LACP configuration it will take a few different API calls. First a Link Aggregation Group (LAG) interface must be created. You will define a Name, specify the state and the LAG-type of LACP, and define which VLANs will use this LAG interface. In the example below, two LAG interfaces are being created (Arista & HA-Interconnect): .. code-block:: bash PATCH https://{{rseries_appliance1_ip}}:8888/restconf/data/ .. code-block:: json { "openconfig-interfaces:interfaces": { "interface": [ { "name": "Arista", "config": { "name": "Arista", "type": "iana-if-type:ieee8023adLag", "enabled": true }, "openconfig-if-aggregate:aggregation": { "config": { "lag-type": "LACP", "f5-if-aggregate:distribution-hash": "src-dst-ipport" }, "openconfig-vlan:switched-vlan": { "config": { "trunk-vlans": [ 3010, 3011 ] } } } }, { "name": "HA-Interconnect", "config": { "name": "HA-Interconnect", "type": "iana-if-type:ieee8023adLag", "enabled": true }, "openconfig-if-aggregate:aggregation": { "config": { "lag-type": "LACP", "f5-if-aggregate:distribution-hash": "src-dst-ipport" }, "openconfig-vlan:switched-vlan": { "config": { "trunk-vlans": [ 500, 501, 502, 503 ] } } } } ] } } The next step is to add physical interfaces into the LAG group. Interfaces will be added to the aggregate-id that was created in the previous step. In this case, interfaces 1.0 and 2.0 will be added to the LAG called **Arista** and interfaces 8.0 and 9.0 will be added to the interface called **HA-Interconnect**. .. code-block:: bash PATCH https://{{rseries_appliance1_ip}}:8888/restconf/data/ .. code-block:: json { "openconfig-interfaces:interfaces": { "interface": [ { "name": "1.0", "config": { "name": "1.0" }, "openconfig-if-ethernet:ethernet": { "config": { "openconfig-if-aggregate:aggregate-id": "Arista" } } }, { "name": "2.0", "config": { "name": "2.0" }, "openconfig-if-ethernet:ethernet": { "config": { "openconfig-if-aggregate:aggregate-id": "Arista" } } }, { "name": "8.0", "config": { "name": "8.0" }, "openconfig-if-ethernet:ethernet": { "config": { "openconfig-if-aggregate:aggregate-id": "HA-Interconnect" } } }, { "name": "9.0", "config": { "name": "9.0" }, "openconfig-if-ethernet:ethernet": { "config": { "openconfig-if-aggregate:aggregate-id": "HA-Interconnect" } } } ] } } The final step is adding LACP configuration for each LAG with the LACP mode **ACTIVE** and the Interval to **FAST**: .. code-block:: bash PATCH https://{{rseries_appliance1_ip}}:8888/restconf/data/ .. code-block:: json { "ietf-restconf:data": { "openconfig-lacp:lacp": { "interfaces": { "interface": [ { "name": "Arista", "config": { "name": "Arista", "interval": "FAST", "lacp-mode": "ACTIVE" } }, { "name": "HA-Interconnect", "config": { "name": "HA-Interconnect", "interval": "FAST", "lacp-mode": "ACTIVE" } } ] } } } } To view the final LAG configuration and status via the API, use the following API call: .. code-block:: bash GET https://{{rseries_appliance1_ip}}:8888/restconf/data/openconfig-lacp:lacp .. code-block:: json { "openconfig-lacp:lacp": { "config": { "system-priority": 32768 }, "state": { "f5-lacp:system-id-mac": "00:94:a1:69:35:13" }, "interfaces": { "interface": [ { "name": "Arista", "config": { "name": "Arista", "interval": "FAST", "lacp-mode": "ACTIVE" }, "state": { "name": "Arista", "interval": "FAST", "lacp-mode": "ACTIVE", "system-id-mac": "0:94:a1:69:35:13" }, "members": { "member": [ { "interface": "1.0", "state": { "activity": "ACTIVE", "timeout": "SHORT", "synchronization": "IN_SYNC", "aggregatable": true, "collecting": true, "distributing": true, "system-id": "0:94:a1:69:35:13", "oper-key": 2, "partner-id": "2c:dd:e9:90:88:13", "partner-key": 103, "port-num": 1024, "partner-port-num": 345, "counters": { "lacp-in-pkts": "236597", "lacp-out-pkts": "7873", "lacp-rx-errors": "0", "lacp-tx-errors": "0", "lacp-unknown-errors": "0", "lacp-errors": "0" } } }, { "interface": "2.0", "state": { "activity": "ACTIVE", "timeout": "SHORT", "synchronization": "IN_SYNC", "aggregatable": true, "collecting": true, "distributing": true, "system-id": "0:94:a1:69:35:13", "oper-key": 2, "partner-id": "2c:dd:e9:90:88:13", "partner-key": 103, "port-num": 2048, "partner-port-num": 349, "counters": { "lacp-in-pkts": "236584", "lacp-out-pkts": "7872", "lacp-rx-errors": "0", "lacp-tx-errors": "0", "lacp-unknown-errors": "0", "lacp-errors": "0" } } } ] } }, { "name": "HA-Interconnect", "config": { "name": "HA-Interconnect", "interval": "FAST", "lacp-mode": "ACTIVE" }, "state": { "name": "HA-Interconnect", "interval": "FAST", "lacp-mode": "ACTIVE", "system-id-mac": "0:94:a1:69:35:13" }, "members": { "member": [ { "interface": "8.0", "state": { "activity": "ACTIVE", "timeout": "SHORT", "synchronization": "IN_SYNC", "aggregatable": true, "collecting": true, "distributing": true, "system-id": "0:94:a1:69:35:13", "oper-key": 3, "partner-id": "0:94:a1:69:29:13", "partner-key": 3, "port-num": 8192, "partner-port-num": 8192, "counters": { "lacp-in-pkts": "236491", "lacp-out-pkts": "236001", "lacp-rx-errors": "0", "lacp-tx-errors": "0", "lacp-unknown-errors": "0", "lacp-errors": "0" } } }, { "interface": "9.0", "state": { "activity": "ACTIVE", "timeout": "SHORT", "synchronization": "IN_SYNC", "aggregatable": true, "collecting": true, "distributing": true, "system-id": "0:94:a1:69:35:13", "oper-key": 3, "partner-id": "0:94:a1:69:29:13", "partner-key": 3, "port-num": 9216, "partner-port-num": 9216, "counters": { "lacp-in-pkts": "236485", "lacp-out-pkts": "235995", "lacp-rx-errors": "0", "lacp-tx-errors": "0", "lacp-unknown-errors": "0", "lacp-errors": "0" } } } ] } } ] } } } You can get more granular information down to the interface level using the following API command: .. code-block:: bash GET https://{{rseries_appliance1_ip}}:8888/restconf/data/openconfig-interfaces:interfaces .. code-block:: json { "openconfig-interfaces:interfaces": { "interface": [ { "name": "1.0", "config": { "name": "1.0", "type": "iana-if-type:ethernetCsmacd", "description": "Interface 1.0", "enabled": true }, "state": { "name": "1.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 9, "oper-status": "UP", "counters": { "in-octets": "61747342", "in-unicast-pkts": "11", "in-broadcast-pkts": "435841", "in-multicast-pkts": "252797", "in-discards": "286", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "1008256", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "7877", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_UP" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_100GB", "openconfig-if-aggregate:aggregate-id": "Arista" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_100GB", "hw-mac-address": "00:94:a1:69:35:03", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "2.0", "config": { "name": "2.0", "type": "iana-if-type:ethernetCsmacd", "description": "Interface 2.0", "enabled": true }, "state": { "name": "2.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 14, "oper-status": "UP", "counters": { "in-octets": "77691305", "in-unicast-pkts": "0", "in-broadcast-pkts": "460498", "in-multicast-pkts": "370834", "in-discards": "201", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "1013768", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "7936", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_UP" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_100GB", "openconfig-if-aggregate:aggregate-id": "Arista" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_100GB", "hw-mac-address": "00:94:a1:69:35:08", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "3.0", "config": { "name": "3.0", "type": "iana-if-type:ethernetCsmacd", "description": "Interface 3.0", "enabled": true }, "state": { "name": "3.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 10, "oper-status": "DOWN", "counters": { "in-octets": "0", "in-unicast-pkts": "0", "in-broadcast-pkts": "0", "in-multicast-pkts": "0", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "0", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "0", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_DEFAULTED" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_25GB" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "hw-mac-address": "00:94:a1:69:35:04", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "4.0", "config": { "name": "4.0", "type": "iana-if-type:ethernetCsmacd", "description": "Interface 4.0", "enabled": true }, "state": { "name": "4.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 11, "oper-status": "DOWN", "counters": { "in-octets": "0", "in-unicast-pkts": "0", "in-broadcast-pkts": "0", "in-multicast-pkts": "0", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "0", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "0", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_DEFAULTED" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_25GB" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "hw-mac-address": "00:94:a1:69:35:05", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "5.0", "config": { "name": "5.0", "type": "iana-if-type:ethernetCsmacd", "description": "Interface 5.0", "enabled": true }, "state": { "name": "5.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 12, "oper-status": "DOWN", "counters": { "in-octets": "0", "in-unicast-pkts": "0", "in-broadcast-pkts": "0", "in-multicast-pkts": "0", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "0", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "0", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_DEFAULTED" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_25GB" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "hw-mac-address": "00:94:a1:69:35:06", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "6.0", "config": { "name": "6.0", "type": "iana-if-type:ethernetCsmacd", "description": "Interface 6.0", "enabled": true }, "state": { "name": "6.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 13, "oper-status": "DOWN", "counters": { "in-octets": "0", "in-unicast-pkts": "0", "in-broadcast-pkts": "0", "in-multicast-pkts": "0", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "0", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "0", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_DEFAULTED" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_25GB" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "hw-mac-address": "00:94:a1:69:35:07", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "7.0", "config": { "name": "7.0", "type": "iana-if-type:ethernetCsmacd", "description": "Interface 7.0", "enabled": true }, "state": { "name": "7.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 15, "oper-status": "DOWN", "counters": { "in-octets": "0", "in-unicast-pkts": "0", "in-broadcast-pkts": "0", "in-multicast-pkts": "0", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "0", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "0", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_DEFAULTED" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_25GB" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "hw-mac-address": "00:94:a1:69:35:09", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "8.0", "config": { "name": "8.0", "type": "iana-if-type:ethernetCsmacd", "description": "Interface 8.0", "enabled": true }, "state": { "name": "8.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 16, "oper-status": "UP", "counters": { "in-octets": "30289796", "in-unicast-pkts": "0", "in-broadcast-pkts": "0", "in-multicast-pkts": "236647", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "30226820", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "236155", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_UP" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "openconfig-if-aggregate:aggregate-id": "HA-Interconnect" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "hw-mac-address": "00:94:a1:69:35:0a", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "9.0", "config": { "name": "9.0", "type": "iana-if-type:ethernetCsmacd", "description": "Interface 9.0", "enabled": true }, "state": { "name": "9.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 17, "oper-status": "UP", "counters": { "in-octets": "30286208", "in-unicast-pkts": "0", "in-broadcast-pkts": "0", "in-multicast-pkts": "236611", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "30223488", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "236121", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_UP" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "openconfig-if-aggregate:aggregate-id": "HA-Interconnect" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "hw-mac-address": "00:94:a1:69:35:0b", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "10.0", "config": { "name": "10.0", "type": "iana-if-type:ethernetCsmacd", "description": "Interface 10.0", "enabled": true }, "state": { "name": "10.0", "type": "iana-if-type:ethernetCsmacd", "mtu": 9600, "enabled": true, "ifindex": 18, "oper-status": "DOWN", "counters": { "in-octets": "0", "in-unicast-pkts": "0", "in-broadcast-pkts": "0", "in-multicast-pkts": "0", "in-discards": "0", "in-errors": "0", "in-fcs-errors": "0", "out-octets": "0", "out-unicast-pkts": "0", "out-broadcast-pkts": "0", "out-multicast-pkts": "0", "out-discards": "0", "out-errors": "0" }, "f5-interface:forward-error-correction": "auto", "f5-lacp:lacp_state": "LACP_DEFAULTED" }, "openconfig-if-ethernet:ethernet": { "config": { "port-speed": "openconfig-if-ethernet:SPEED_25GB" }, "state": { "port-speed": "openconfig-if-ethernet:SPEED_25GB", "hw-mac-address": "00:94:a1:69:35:0c", "counters": { "in-mac-control-frames": "0", "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-8021q-frames": "0", "in-crc-errors": "0", "out-mac-control-frames": "0", "out-mac-pause-frames": "0", "out-8021q-frames": "0" }, "f5-if-ethernet:flow-control": { "rx": "on" } } } }, { "name": "mgmt", "config": { "name": "mgmt", "type": "iana-if-type:ethernetCsmacd", "enabled": true }, "state": { "name": "mgmt", "type": "iana-if-type:ethernetCsmacd", "enabled": true, "ifindex": 1, "oper-status": "UP", "counters": { "in-octets": "248626571", "in-unicast-pkts": "135122", "in-broadcast-pkts": "1565287", "in-multicast-pkts": "363729", "in-discards": "0", "in-errors": "0", "out-octets": "858981655", "out-unicast-pkts": "611399", "out-broadcast-pkts": "41", "out-multicast-pkts": "60", "out-discards": "0", "out-errors": "0" } }, "openconfig-if-ethernet:ethernet": { "config": { "auto-negotiate": true, "duplex-mode": "FULL", "port-speed": "openconfig-if-ethernet:SPEED_1GB" }, "state": { "auto-negotiate": true, "duplex-mode": "FULL", "port-speed": "openconfig-if-ethernet:SPEED_1GB", "hw-mac-address": "00:94:a1:69:35:02", "negotiated-duplex-mode": "FULL", "negotiated-port-speed": "openconfig-if-ethernet:SPEED_1GB", "counters": { "in-mac-pause-frames": "0", "in-oversize-frames": "0", "in-jabber-frames": "0", "in-fragment-frames": "0", "in-crc-errors": "0", "out-mac-pause-frames": "0" } } } }, { "name": "Arista", "config": { "name": "Arista", "type": "iana-if-type:ieee8023adLag", "enabled": true }, "state": { "name": "Arista", "type": "iana-if-type:ieee8023adLag", "mtu": 9600, "enabled": true, "oper-status": "UP", "f5-interface:forward-error-correction": "auto" }, "openconfig-if-aggregate:aggregation": { "config": { "lag-type": "LACP", "f5-if-aggregate:distribution-hash": "src-dst-ipport" }, "state": { "lag-type": "LACP", "lag-speed": 200, "f5-if-aggregate:distribution-hash": "src-dst-ipport", "f5-if-aggregate:mac-address": "00:94:a1:69:35:14", "f5-if-aggregate:lagid": 1 }, "openconfig-vlan:switched-vlan": { "config": { "trunk-vlans": [ 3010, 3011 ] } } } }, { "name": "HA-Interconnect", "config": { "name": "HA-Interconnect", "type": "iana-if-type:ieee8023adLag", "enabled": true }, "state": { "name": "HA-Interconnect", "type": "iana-if-type:ieee8023adLag", "mtu": 9600, "enabled": true, "oper-status": "UP", "f5-interface:forward-error-correction": "auto" }, "openconfig-if-aggregate:aggregation": { "config": { "lag-type": "LACP", "f5-if-aggregate:distribution-hash": "src-dst-ipport" }, "state": { "lag-type": "LACP", "lag-speed": 50, "f5-if-aggregate:distribution-hash": "src-dst-ipport", "f5-if-aggregate:mac-address": "00:94:a1:69:35:15", "f5-if-aggregate:lagid": 2 }, "openconfig-vlan:switched-vlan": { "config": { "trunk-vlans": [ 500, 501, 502, 503 ] } } } } ] } }