wom local-endpoint
wom local-endpoint(1) BIG-IP TMSH Manual wom local-endpoint(1)
NAME
local-endpoint - Configures the local endpoint for the WAN Optimization Manager.
MODULE
wom
SYNTAX
Configure the local-endpoint component within the wom module using the following syntax.
CREATE/MODIFY
create local-endpoint
modify local-endpoint
options:
addresses [add | delete | replace-all-with] {
[ip address]
}
addresses none
allow-nat [disabled | enabled]
description [string]
endpoint [disabled | enabled]
internal-forwarding [disabled | enabled]
ip-encap-mtu [unsigned integer]
ip-encap-profile [none | profile name]
ip-encap-type [gre | ipip | ipsec | none]
no-route [drop | passthru]
server-ssl [none | profile name]
snat [local | none | remote]
tunnel-port [unsigned integer]
DISPLAY
list local-endpoint
show local-endpoint
show running-config local-endpoint
options:
all-properties
non-default-properties
one-line
DELETE
delete local-endpoint
DESCRIPTION
You can use the local-endpoint component to modify the settings for the local endpoint for the WAN Optimization Manager on
the local BIG-IP(r) system.
EXAMPLES
modify local-endpoint allow-nat disabled
Disables the allow-nat option, specifying that the system does not accept connections for traffic behind a Network
Address Translation (NAT) device.
list local-endpoint all-properties
Displays all of the properties of the local-endpoint component.
OPTIONS
addresses
Specifies a single IP address the system uses for the local endpoint. The IP address must be in the same subnet as a
self IP address on the BIG-IP(r) system.
allow-nat
When enabled, specifies that the system accepts connections for traffic behind a Network Address Translation device.
The default value is enabled.
description
User defined description.
endpoint
When enabled, specifies that the local endpoint is available for initiating and receiving optimized traffic. The
default value is enabled.
To turn off WAN optimization on this endpoint, use disabled.
internal-forwarding
When enabled, specifies that the local endpoint is available for forwarding internal traffic to remote endpoints. The
default value is disabled.
This parameter works only if internal-forwarding for remote-endpoint is set to default.
ip-encap-mtu
Specifies the maximum transfer unit for IP encapsulated traffic.
ip-encap-profile
Specifies the name of the profile with the encapsulation settings. This profile must be of the type specified for the
setting ip-encap-type.
ip-encap-type
Specifies the type of IP layer encapsulation to perform on iSession(tm) traffic.
The default value is none. The options are:
gre The system uses the Generic Routing Encapsulation (GRE) tunneling protocol.
ipip The system uses the IP over IP (IPIP) tunneling protocol.
ipsec
The system uses IP security (IPsec) encapsulation.
none No IP encapsulation takes place.
no-route
Specifies what the system does with traffic for which there is no remote endpoint to complete the iSession connection.
The default value is passthru. The options are:
drop The system terminates the traffic flow.
passthru
The traffic flow continues without an iSession connection.
server-ssl
Specifies the default server SSL profile the system uses for all encrypted outbound connections. The default value is
none.
snat Specifies the IP address the system uses for incoming traffic as the source IP address of the TCP connection between
the WAN Optimization Manager and the server.
The default value is none. The options are:
local
The system uses the endpoint IP address closest to the destination. Use this setting to make sure the return
route also goes through the BIG-IP system, so that both sides of the connection can be optimized. This setting is
useful if responses returning from the server to the client would not normally pass through the BIG-IP system.
none The system uses the original connecting client IP address.
remote
The system uses the source IP address of the incoming iSession connection. Use this setting when an appliance
that uses NAT is located between the WAN Optimization endpoints.
tunnel-port
Specifies the number of the port on the local endpoint that the WAN Optimization Manager uses for control connections.
The port must have access through the firewall. The range is from 1 to 65535. The default value is 443.
SEE ALSO
list, modify, show, tmsh, wom advertised-route, wom remote-endpoint
COPYRIGHT
No part of this program may be reproduced or transmitted in any form or by any means, electronic or mechanical, including
photocopying, recording, or information storage and retrieval systems, for any purpose other than the purchaser's personal
use, without the express written permission of F5 Networks, Inc.
F5 Networks and BIG-IP (c) Copyright 2009-2013. All rights reserved.
BIG-IP 2014-05-08 wom local-endpoint(1)