wom remote-endpoint¶

wom remote-endpoint(1) BIG-IP TMSH Manual wom remote-endpoint(1)

NAME
remote-endpoint - Configures one or more remote endpoints for the WAN Optimization Manager.

MODULE
wom

SYNTAX
Configure the remote-endpoint component within the wom module using the following syntax.

DISPLAY
list remote-endpoint
list remote-endpoint [name]
show running-config remote-endpoint
show running-config remote-endpoint [name]
options:
all-properties
dedup-codec
non-default-properties
one-line

show remote-endpoint
show remote-endpoint [name]
options:
(default | exa | gig | kil | meg | peta | raw | tera | yotta | zetta)

DELETE
delete remote-endpoint [name]

Note: If you delete a remote endpoint without also disabling the endpoint-discovery component, the remote endpoint may
reappear as it is rediscovered. To remove a remote endpoint from traffic initiated by this WAN Optimization Manager, set
the endpoint option of the remote-endpoint component to disabled.

DESCRIPTION
You can use the remote-endpoint component to create, modify, or delete a remote endpoint for traffic from the local WAN
Optimization Manager.

EXAMPLES
modify remote-endpoint 13.16.0.5 endpoint disabled

Disables the WAN optimization connection to the remote endpoint that is named 13.16.0.5.

list remote-endpoint all-properties

Displays all the properties of all the remote endpoints for traffic from the local WAN Optimization Manager.

OPTIONS
allow-routing
Specifies whether there is a route from the local endpoint to this remote endpoint through which the local endpoint
can establish connections. The default value is enabled.

address
Specifies the IP address of the remote endpoint.

app-service
Specifies the name of the application service to which the object belongs. The default value is none. Note: If the
strict-updates option is enabled on the application service that owns the object, you cannot modify or delete the
object. Only the application service can modify or delete the object.

description
User defined description.

dedup-action
Clears the cache used for symmetric data deduplication on the specified remote endpoint and immediately resets the
value to none.

dedup-codec
Displays the deduplication codec used by the remote endpoint: sdd-v2 or sdd-v3.

endpoint
When enabled, specifies that traffic can be optimized between the local and remote endpoints. The default value is
enabled.

Note: Disabling a remote endpoint affects only the connection between the local endpoint and this remote endpoint.

internal-forwarding
When enabled, specifies that the remote endpoint is available for forwarding internal traffic.

When disabled, specifies that the remote endpoint is NOT available for forwarding internal traffic.

When default, specifies that forwarding internal traffic is managed by the local-endpoint.internal-forwarding setting.

The default value is default.

ip-encap-mtu
Specifies the maximum transfer unit for IP encapsulated traffic. The default value is 0.

ip-encap-profile
Specifies the name of a profile with encapsulation settings. This profile must be of the type specified for the
setting ip-encap-type.

ip-encap-type
Specifies the type of IP layer encapsulation performed on iSession traffic.

The default value is default. The options are:

default
The system uses the ip-encap-type value set for the local endpoint.

gre The system uses the Generic Routing Encapsulation (GRE) tunneling protocol.

ipip The system uses the IP over IP (IPIP) tunneling protocol.

ipsec
The system uses IP security (IPsec) encapsulation.

none No IP encapsulation takes place.

origin
Specifies whether the remote endpoint was discovered automatically or configured manually.

The options are:

configured
Indicates that you manually configured this remote endpoint. The system automatically sets this value, and you
cannot change it.

discovered
Indicates that the system automatically discovered this remote endpoint. Note that endpoints for which the value
of the origin property is discovered are not saved to the file bigip_local.conf.

manually-saved
After you run the command save / sys config, the value of the origin property that was set to persistable changes
to manually-saved. Note that after the system changes the value to manually-saved, you cannot change it again.

persistable
Change the origin from discovered to persistable, if you want to save the endpoint to the file bigip_local.conf
when you use the command save / sys config.

server-ssl
Specifies the server SSL profile the system uses to connect to this remote endpoint. This setting overrides the
server-ssl setting for the local-endpoint component. The default value is none.

snat Specifies the IP address the system uses as the source IP address of the TCP connection between the WAN Optimization
Manager and the server.

The default value is default. The options are:

default
The system uses the snat value set for the local-endpoint component.

local
The system uses the endpoint IP address closest to the destination. Use this setting to make sure the return
route also goes through the BIG-IP system, so that both sides of the connection can be optimized. This setting is
useful if responses returning from the server to the client would not normally pass through the BIG-IP system.

none The system uses the original connecting client IP address.

remote
The system uses the source IP address of the incoming iSession connection. Use this setting when an appliance
that uses NAT is located between the WAN Optimization Manager endpoints.

tunnel-encrypt
Enables or disables encryption of traffic passing between the two WAN Optimization Managers. The default value is
enabled

tunnel-port
Specifies whether to use a specific port for traffic optimized to this endpoint or to use port transparency (0). The
default value is 443.

SEE ALSO
create, delete, list, modify, show, tmsh, wom advertised-route, wom local-endpoint

COPYRIGHT
No part of this program may be reproduced or transmitted in any form or by any means, electronic or mechanical, including
photocopying, recording, or information storage and retrieval systems, for any purpose other than the purchaser's personal
use, without the express written permission of F5 Networks, Inc.

BIG-IP 2014-05-08 wom remote-endpoint(1)