ltm profile udp
ltm profile udp(1) BIG-IP TMSH Manual ltm profile udp(1)
NAME
udp - Configures a User Datagram Protocol (UDP) profile.
MODULE
ltm profile
SYNTAX
Configure the udp component within the ltm profile module using the
syntax shown in the following sections.
CREATE/MODIFY
create udp [name]
modify udp [name]
options:
allow-no-payload [disabled | enabled]
app-service [[string] | none]
buffer-max-bytes [integer]
buffer-max-packets [integer]
datagram-load-balancing [disabled | enabled]
defaults-from [[name] | none]
description [string]
idle-timeout [immediate | indefinite | integer]
ip-tos-to-client [[integer] | pass-through]
link-qos-to-client [[integer] | pass-through]
no-checksum [disabled | enabled]
proxy-mss [disabled | enabled]
ip-ttl-mode [proxy | preserve | decrement | set]
ip-ttl-v4 [integer]
ip-ttl-v6 [integer]
ip-df-mode [pmtu | preserve | set | clear]
edit udp [ [ [name] | [glob] | [regex] ] ... ]
options:
all-properties
non-default-properties
mv udp [ [[source-name] [destination-name]] | [[name] to-folder [folder-name]] | [[name...name] to-folder [folder-name]] ]
options:
to-folder
reset-stats udp
reset-stats udp [ [ [name] | [glob] | [regex] ] ... ]
DISPLAY
list udp
list udp [ [ [name] | [glob] | [regex] ] ... ]
show running-config udp
show running-config udp
[ [ [name] | [glob] | [regex] ] ... ]
options:
all-properties
non-default-properties
one-line
partition
show udp
show udp [ [ [name] | [glob] | [regex] ] ... ]
options:
(default | exa | gig | kil | meg | peta | raw | tera | yotta | zetta)
field-fmt
global
DELETE
delete udp [name]
DESCRIPTION
You can use the udp component to manage UDP network traffic.
EXAMPLES
create udp my_udp_profile defaults-from udp
Creates a custom UDP profile named my_udp_profile that inherits its
settings from the system default UDP profile.
list udp all-properties
Displays all properties for all UDP profiles.
mv udp /Common/my_udp_profile to-folder /Common/my_folder
Moves a custom udp profile named my_udp_profile to a folder named
my_folder, where my_folder has already been created and exists within
/Common.
OPTIONS
allow-no-payload
Provides the ability to allow the passage of datagrams that
contain header information, but no essential data. The default is
disabled.
app-service
Specifies the name of the application service to which the profile
belongs. The default value is none. Note: If the strict-updates
option is enabled on the application service that owns the object,
you cannot modify or delete the profile. Only the application
service can modify or delete the profile.
buffer-max-bytes
Specifies ingress buffer byte limit. The default value is 655350.
Maximum allowed value is 16777215.
buffer-max-packets
Specifies ingress buffer packet limit. The default value is 10.
Maximum allowed value is 255.
datagram-load-balancing
Provides the ability to load balance UDP datagram by datagram. The
default is disabled.
defaults-from
Specifies the profile that you want to use as the parent profile.
Your new profile inherits all settings and values from the parent
profile. The default value is udp.
description
User defined description.
glob Displays the items that match the glob expression. See help glob
for a description of glob expression syntax.
idle-timeout
Specifies the number of seconds that a connection is idle before
the connection is eligible for deletion. The default value is 60
seconds.
ip-tos-to-client
Specifies the Type of Service level that the traffic management
system assigns to UDP packets when sending them to clients. The
default value is 0 (zero).
ip-ttl-mode
Describe the outgoing UDP packet's TTL mode. Modes are: Proxy: Set
the IP TTL of ipv4 to the default value of 255 and ipv6 to the
default value of 64. Preserve: Set the IP TTL to the original
packet TTL value. Decrement: Set the IP TTL to the original
packet TTL value minus 1. Set: Set the IP TTL with the specified
values in ip-ttl-v4 and ip-ttl-v6 values in the same profile.
ip-df-mode
Describe the Don't Fragment (DF) bit setting in the outgoing UDP
packet. Pmtu: Set the outgoing UDP packet DF big based on the ip
pmtu setting. Preserve: Preserve the incoming UDP packet Don't
Fragment bit. Set: Set the outgoing UDP packet DF bit. Clear:
Clear the outgoing UDP packet DF bit.
link-qos-to-client
Specifies the Quality of Service level that the system assigns to
UDP packets when sending them to clients. The default value is 0
(zero).
name Specifies a unique name for the component. This option is required
for the commands create, delete, and modify.
no-checksum
Enables or disables checksum processing. Note that if the datagram
is IPv6, the system always performs checksum processing. The
default value is disabled.
partition
Displays the administrative partition within which the profile
resides.
proxy-mss
Specifies, when enabled, that the system advertises the same mss
to the server as was negotiated with the client. The default value
is disabled.
regex
Displays the items that match the regular expression. The regular
expression must be preceded by an at sign (@[regular expression])
to indicate that the identifier is a regular expression. See help
regex for a description of regular expression syntax.
to-folder
udp profiles can be moved to any folder under /Common, but
configuration dependencies may restrict moving the profile out of
/Common.
SEE ALSO
create, delete, edit, glob, ltm profile, ltm virtual, modify, mv, show,
regex, reset-stats, tmsh
COPYRIGHT
No part of this program may be reproduced or transmitted in any form or
by any means, electronic or mechanical, including photocopying,
recording, or information storage and retrieval systems, for any
purpose other than the purchaser's personal use, without the express
written permission of F5 Networks, Inc.
F5 Networks and BIG-IP (c) Copyright 2008-2010, 2012-2013. All rights
reserved.
BIG-IP 2016-08-22 ltm profile udp(1)