wom remote-endpoint
wom remote-endpoint(1) BIG-IP TMSH Manual wom remote-endpoint(1)
NAME
remote-endpoint - Configures one or more remote endpoints for the WAN
Optimization Manager.
MODULE
wom
SYNTAX
Configure the remote-endpoint component within the wom module using the
following syntax.
CREATE/MODIFY
create remote-endpoint [name]
modify remote-endpoint [name]
options:
address [ip address]
allow-routing [disabled | enabled]
app-service [[string] | none]
dedup-action [none | cache-refresh]
description [string]
endpoint [disabled | enabled]
internal-forwarding [default | disabled | enabled]
ip-encap-mtu [unsigned integer]
ip-encap-profile [none | profile name]
ip-encap-type [default | gre | ipip | ipsec | none]
origin [configured | discovered | manually-saved | persistable]
server-ssl [none | profile name]
snat [default | local | none | remote]
tunnel-encrypt [disabled | enabled]
tunnel-port [unsigned integer]
reset-stats remote-endpoint
DISPLAY
list remote-endpoint
list remote-endpoint [name]
show running-config remote-endpoint
show running-config remote-endpoint [name]
options:
all-properties
dedup-codec
non-default-properties
one-line
show remote-endpoint
show remote-endpoint [name]
options:
(default | exa | gig | kil | meg | peta | raw | tera | yotta | zetta)
DELETE
delete remote-endpoint [name]
Note: If you delete a remote endpoint without also disabling the
endpoint-discovery component, the remote endpoint may reappear as it is
rediscovered. To remove a remote endpoint from traffic initiated by
this WAN Optimization Manager, set the endpoint option of the remote-
endpoint component to disabled.
DESCRIPTION
You can use the remote-endpoint component to create, modify, or delete
a remote endpoint for traffic from the local WAN Optimization Manager.
EXAMPLES
modify remote-endpoint 13.16.0.5 endpoint disabled
Disables the WAN optimization connection to the remote endpoint
that is named 13.16.0.5.
list remote-endpoint all-properties
Displays all the properties of all the remote endpoints for
traffic from the local WAN Optimization Manager.
OPTIONS
allow-routing
Specifies whether there is a route from the local endpoint to this
remote endpoint through which the local endpoint can establish
connections. The default value is enabled.
address
Specifies the IP address of the remote endpoint.
app-service
Specifies the name of the application service to which the object
belongs. The default value is none. Note: If the strict-updates
option is enabled on the application service that owns the object,
you cannot modify or delete the object. Only the application
service can modify or delete the object.
description
User defined description.
dedup-action
Clears the cache used for symmetric data deduplication on the
specified remote endpoint and immediately resets the value to
none.
dedup-codec
Displays the deduplication codec used by the remote endpoint:
sdd-v2 or sdd-v3.
endpoint
When enabled, specifies that traffic can be optimized between the
local and remote endpoints. The default value is enabled.
Note: Disabling a remote endpoint affects only the connection
between the local endpoint and this remote endpoint.
internal-forwarding
When enabled, specifies that the remote endpoint is available for
forwarding internal traffic.
When disabled, specifies that the remote endpoint is NOT available
for forwarding internal traffic.
When default, specifies that forwarding internal traffic is
managed by the local-endpoint.internal-forwarding setting.
The default value is default.
ip-encap-mtu
Specifies the maximum transfer unit for IP encapsulated traffic.
The default value is 0.
ip-encap-profile
Specifies the name of a profile with encapsulation settings. This
profile must be of the type specified for the setting ip-encap-
type.
ip-encap-type
Specifies the type of IP layer encapsulation performed on iSession
traffic.
The default value is default. The options are:
default
The system uses the ip-encap-type value set for the local
endpoint.
gre The system uses the Generic Routing Encapsulation (GRE)
tunneling protocol.
ipip The system uses the IP over IP (IPIP) tunneling protocol.
ipsec
The system uses IP security (IPsec) encapsulation.
none No IP encapsulation takes place.
origin
Specifies whether the remote endpoint was discovered automatically
or configured manually.
The options are:
configured
Indicates that you manually configured this remote endpoint.
The system automatically sets this value, and you cannot
change it.
discovered
Indicates that the system automatically discovered this
remote endpoint. Note that endpoints for which the value of
the origin property is discovered are not saved to the file
bigip_local.conf.
manually-saved
After you run the command save / sys config, the value of the
origin property that was set to persistable changes to
manually-saved. Note that after the system changes the value
to manually-saved, you cannot change it again.
persistable
Change the origin from discovered to persistable, if you want
to save the endpoint to the file bigip_local.conf when you
use the command save / sys config.
server-ssl
Specifies the server SSL profile the system uses to connect to
this remote endpoint. This setting overrides the server-ssl
setting for the local-endpoint component. The default value is
none.
snat Specifies the IP address the system uses as the source IP address
of the TCP connection between the WAN Optimization Manager and the
server.
The default value is default. The options are:
default
The system uses the snat value set for the local-endpoint
component.
local
The system uses the endpoint IP address closest to the
destination. Use this setting to make sure the return route
also goes through the BIG-IP system, so that both sides of
the connection can be optimized. This setting is useful if
responses returning from the server to the client would not
normally pass through the BIG-IP system.
none The system uses the original connecting client IP address.
remote
The system uses the source IP address of the incoming
iSession connection. Use this setting when an appliance that
uses NAT is located between the WAN Optimization Manager
endpoints.
tunnel-encrypt
Enables or disables encryption of traffic passing between the two
WAN Optimization Managers. The default value is enabled
tunnel-port
Specifies whether to use a specific port for traffic optimized to
this endpoint or to use port transparency (0). The default value
is 443.
SEE ALSO
create, delete, list, modify, show, tmsh, wom advertised-route, wom
local-endpoint
COPYRIGHT
No part of this program may be reproduced or transmitted in any form or
by any means, electronic or mechanical, including photocopying,
recording, or information storage and retrieval systems, for any
purpose other than the purchaser's personal use, without the express
written permission of F5 Networks, Inc.
F5 Networks and BIG-IP (c) Copyright 2009-2012. All rights reserved.
BIG-IP 2014-05-08 wom remote-endpoint(1)