wom local-endpoint¶

wom local-endpoint(1) BIG-IP TMSH Manual wom local-endpoint(1)

NAME
local-endpoint - Configures the local endpoint for the WAN Optimization Manager.

MODULE
wom

SYNTAX
Configure the local-endpoint component within the wom module using the following syntax.

CREATE/MODIFY
create local-endpoint
modify local-endpoint
options:
addresses [add | delete | replace-all-with] {
[ip address]
}
addresses none
allow-nat [disabled | enabled]
description [string]
endpoint [disabled | enabled]
internal-forwarding [disabled | enabled]
ip-encap-mtu [unsigned integer]
ip-encap-profile [none | profile name]
ip-encap-type [gre | ipip | ipsec | none]
no-route [drop | passthru]
server-ssl [none | profile name]
snat [local | none | remote]
tunnel-port [unsigned integer]

DISPLAY
list local-endpoint
show local-endpoint
show running-config local-endpoint
options:
all-properties
non-default-properties
one-line

DELETE
delete local-endpoint

DESCRIPTION
You can use the local-endpoint component to modify the settings for the local endpoint for the WAN
Optimization Manager on the local BIG-IP(r) system.

EXAMPLES
modify local-endpoint allow-nat disabled

Disables the allow-nat option, specifying that the system does not accept connections for traffic behind
a Network Address Translation (NAT) device.

list local-endpoint all-properties

Displays all of the properties of the local-endpoint component.

OPTIONS
addresses
Specifies a single IP address the system uses for the local endpoint. The IP address must be in the same
subnet as a self IP address on the BIG-IP(r) system.

allow-nat
When enabled, specifies that the system accepts connections for traffic behind a Network Address
Translation device. The default value is enabled.

description
User defined description.

endpoint
When enabled, specifies that the local endpoint is available for initiating and receiving optimized
traffic. The default value is enabled.

To turn off WAN optimization on this endpoint, use disabled.

internal-forwarding
When enabled, specifies that the local endpoint is available for forwarding internal traffic to remote
endpoints. The default value is disabled.

This parameter works only if internal-forwarding for remote-endpoint is set to default.

ip-encap-mtu
Specifies the maximum transfer unit for IP encapsulated traffic.

ip-encap-profile
Specifies the name of the profile with the encapsulation settings. This profile must be of the type
specified for the setting ip-encap-type.

ip-encap-type
Specifies the type of IP layer encapsulation to perform on iSession(tm) traffic.

The default value is none. The options are:

gre The system uses the Generic Routing Encapsulation (GRE) tunneling protocol.

ipip The system uses the IP over IP (IPIP) tunneling protocol.

ipsec
The system uses IP security (IPsec) encapsulation.

none No IP encapsulation takes place.

no-route
Specifies what the system does with traffic for which there is no remote endpoint to complete the
iSession connection.

The default value is passthru. The options are:

drop The system terminates the traffic flow.

passthru
The traffic flow continues without an iSession connection.

server-ssl
Specifies the default server SSL profile the system uses for all encrypted outbound connections. The
default value is none.

snat Specifies the IP address the system uses for incoming traffic as the source IP address of the TCP
connection between the WAN Optimization Manager and the server.

The default value is none. The options are:

local
The system uses the endpoint IP address closest to the destination. Use this setting to make sure
the return route also goes through the BIG-IP system, so that both sides of the connection can be
optimized. This setting is useful if responses returning from the server to the client would not
normally pass through the BIG-IP system.

none The system uses the original connecting client IP address.

remote
The system uses the source IP address of the incoming iSession connection. Use this setting when an
appliance that uses NAT is located between the WAN Optimization endpoints.

tunnel-port
Specifies the number of the port on the local endpoint that the WAN Optimization Manager uses for control
connections. The port must have access through the firewall. The range is from 1 to 65535. The default
value is 443.

SEE ALSO
list, modify, show, tmsh, wom advertised-route, wom remote-endpoint

COPYRIGHT
No part of this program may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying, recording, or information storage and retrieval systems, for any purpose
other than the purchaser's personal use, without the express written permission of F5 Networks, Inc.

BIG-IP 2014-05-08 wom local-endpoint(1)